BBK GB feeler thread

L

Logan

iS VIP
iS VIP
Location
Seattle
I've been looking at purchasing a BBK for some time. During the search/re-search process I contacted member Raymond as he has JBT brakes. From what I understand JBT is made by the same factory as Rotora and the build quality is excellent.

Raymond was really helpful and set me up with a contact here in the US that has access to JBT gear at fairly tight factory pricing. I wasn't going to post this feeler as BBK's aren't normally something you see as a GB BUT this appears to be a solid deal.

The quote I received was for 2 - 15" slotted rotors (front and rear), 6 pot calipers front, 4 pot calipers rear. Kit includes: Pads, SS brake lines and brackets for installation. GB price is $3,364.36 for the entire kit, NOT including shipping. I was told that you should allow for three weeks shipping time. You can also get the rotors drilled for an additional cost.

If we can purchase 5 sets the above price is valid.

Caliper shown below in the chrome finish (very shiney) on a Z - They are also available in silver, red and black.

1


JBT site Taiwan - http://www.jbt.com.tw/chinese/products.htm?link=4

If you are interested please PM me and I'll give you the necessary contact information.


[FONT=Tahoma, Verdana, Helvetica, Arial]

[/FONT]​
 
This sounds like a great deal. Good looking out, Lance! I've always wanted the chrome myself. :tup:
 
lance if you can spot me a loan for $3500 interest free paid back over the next 20 years i'm in :wink:


gl! hope this goes through!
 
I wonder if they are truly interchangeable with the Rotora setup. Maybe I can get my replacement rotors and pads through JBT for less.
 
aiya said:
I wonder if they are truly interchangeable with the Rotora setup. Maybe I can get my replacement rotors and pads through JBT for less.
Click to expand...

Possibly, I'll PM you with Michael's contact information, he's a little slow on his communications but he's a really nice guy.

---------- Post added at 12:29 PM ---------- Previous post was at 12:28 PM ----------
aiya said:
If it helps, the Rotoras were direct bolt-ons. The only modification needed was to either trim the rear dust shield or replace them with the one from the FX50S.
Click to expand...

Raymond said that it was a direct bolt up, front and rear.
 
I'll second the interest in the rotors & pads, but rich keep in mind that we are 14" not 15", the hats look different I think the extra inch is there really & I'm guessing this won't be good for the rotoras unless they also make a 14" rotor too... that price is crazy cheap for 15" front & rear...
 
^ Quality is up there as well! Price is slightly higher than originally quoted in my OP BUT includes shipping for GB. and he is saying no tax outside of CA. Check the details below:

For[FONT=Tahoma, Verdana, Helvetica, Arial] GB buyers,

Only option is the Drilled rotor (additional USD$30.00/set).
Available Color in Red, Black and Silver. * No customer color option for GB buyer.
J-NS012F-6D CB6P Ø355/t32/2pcs $1,682.68
J-NS012F-6E CB6P Ø380/t32/2pcs $1,868.29
J-NS012R-4D CB4P Ø355/t32/2pcs $1,461.54
J-NS012R-4E FB4P1Ø380/t34/2pcs $1,673.14
All kit does includes pads, SS brake lines, and brackets, unless specially specify.
* As for GB buyer, if there located in CA, they will have to pay the local CA tax.

As for Shipping, I will do the same for them, free shipping within Lower 48 States.
Hope this can gain some more attention to GB buyer.

Michael

So the price for four 15" rotors at the 6/4 pot combination is 3,541.43 (rather than $3,364.36) or $177.07 more than I posted above BUT it includes shipping and if you don't live in CA (sorry guys) no tax.....

I will be upgrading to the cross drilled option on mine. I prefer the look of the hole pattern over the slots.
[/FONT]
 
Jump on this!!! This a crazy deal for a big brake kit.

Ray said these are the same as Rotora!

Too bad I already have a AP racing kit but this pricing blows them out of the water.
 
turbocad6 said:
I'll second the interest in the rotors & pads, but rich keep in mind that we are 14" not 15", the hats look different I think the extra inch is there really & I'm guessing this won't be good for the rotoras unless they also make a 14" rotor too...
Click to expand...

Logan said:
[FONT=Tahoma, Verdana, Helvetica, Arial]

J-NS012F-6D CB6P Ø355/t32/2pcs $1,682.68
J-NS012F-6E CB6P Ø380/t32/2pcs $1,868.29
J-NS012R-4D CB4P Ø355/t32/2pcs $1,461.54
J-NS012R-4E FB4P1Ø380/t34/2pcs $1,673.14


[/FONT]
Click to expand...
Looks like they have both a 14" and 15" rotor. But no confirmation that they are compatible with the Rotoras...yet. :embarrassed:
 
You must log in or register to reply here.
Back
Top